There are three methods to install the mixing drum of forced concrete mixer on the car chassis

一、是筒口朝向轿车的后方歪斜设置，混凝土从车尾部装进和卸出;

1、 The cylinder opening is inclined to the rear of the car, and the concrete is loaded and unloaded from the rear of the car;

二、是搅拌筒向前歪斜，在搅拌筒前方装料和出料。

2、 Is the mixing drum forward skew, in front of the mixing drum loading and discharging.

三、是整个上车能够回转的斜置搅拌筒。其间以搅拌筒后倾安顿的结构方法多，技术老练。前倾式有驾驶员操作方便之利，但搅拌筒口有必要逾越驾驶室上方，使搅拌筒过长过高，并使组织杂乱，搅拌筒容积利用率也有所下降，惯例设计一般选用搅拌筒后倾安顿。

3、 It is an inclined mixing drum which can be rotated by the whole vehicle. Among them, the most sophisticated structure and method are the backward inclined mixing drum. The forward tilting type has the advantage of convenient operation for the driver, but it is necessary to cross the top of the driver's cab to make the mixing drum too long and too high, and make the organization disorderly, and the volume utilization rate of the mixing drum is also reduced. The conventional design generally uses the backward inclined mixing drum to settle down.

开机后，常常注意混凝土搅拌机http://www.zkhntjbc.com各部件的运转是否正常。停机时，常常查看混凝土搅拌机叶片是否打弯，螺丝有否打落或松动。当混凝土搅拌结束或估量停歇1h以上，除将余料出净外，运用石子和清水倒入抖筒内，开机转动，把粘在料筒上的砂浆冲刷干净后悉数卸出。料筒内不得有积水，以免料筒和叶片生锈。

Attention should be paid to the concrete after starting the mixer http://www.zkhntjbc.com Whether the operation of each component is normal. When stopping the machine, often check whether the blade of the concrete mixer is bent and whether the screw is broken or loose. When the concrete mixing is finished or it is estimated to stop for more than 1 h, in addition to discharging the remaining materials, stone and water are used to pour into the shaking drum, and the machine is started to rotate. The mortar glued to the barrel is washed and discharged. There should be no water in the barrel to avoid rust of the barrel and blade.

运用此类配料机的用户为降低收购本钱，多期望借用配料机的计量斗来一同计量散装水泥，通过水泥螺旋输送机将水泥仓中的水泥打入配料机计量斗，一般不主张此用法，因为水泥流动性好，会形成计量斗口与输送皮带空隙有少量水泥溢出，而形成现场粉尘污染或水泥丢失，如非要运用此方法则有必要选用槽型皮带托辊，且斗口边加设软薄挡边，方能控制水泥外溢。

In order to reduce the purchase cost, users of this kind of batching machine expect to use the metering bucket of batching machine to measure the bulk cement together. The cement in the cement bin is pumped into the metering bucket of the batching machine through the cement screw conveyor. Generally, this method is not advocated because the cement has good fluidity, and a small amount of cement spills from the gap between the metering bucket mouth and the conveyor belt, resulting in on-site dust pollution or If it is necessary to use this rule, it is necessary to select trough type belt idler and set soft and thin rib at the edge of bucket mouth to control cement overflow.

本着实用新型将边臂在整体搅拌臂布局的旋转方向的位置后撤，使其落后于同侧的搅拌臂组的端臂，这样在实际工作时，边臂工作阻力较小、与搅拌筒之间无切磨，使边臂的耐久度前进，搅拌轴所需驱动力也减小，因此可安装小功率的电机，使制造本钱降低，能耗相应减小。

In line with the utility model, the side arm is retracted in the rotation direction of the overall mixing arm layout, so that it lags behind the end arm of the mixing arm group on the same side. In the actual work, the working resistance of the side arm is small, and there is no cutting grinding between the side arm and the mixing drum, so that the durability of the side arm is advanced and the driving force of the mixing shaft is reduced. Therefore, a small power motor can be installed to reduce the manufacturing cost and energy consumption Decrease accordingly.