什么原因导致搅拌机存在抱轴问题呢？小型搅拌机厂家认为可能是原料投料位置问题。搅拌混凝土所用的物料主要是砂石骨料、水泥、粉煤灰、水和外加剂等。原料水泥若包裹砂石遇水结块，如果搅拌不充分就容易粘在搅拌轴上，若水泥进料口位置方向不合理，使搅拌轴不能快速充分搅拌，就容易形成抱轴现象。

What causes the shaft holding problem of the mixer? The manufacturer of small mixer thinks that it may be the problem of raw material feeding position. The materials used for mixing concrete are mainly sand aggregate, cement, fly ash, water and additives. If the raw cement is wrapped with sand and gravel and agglomerates in water, it is easy to stick to the mixing shaft if the mixing is not sufficient. If the position and direction of the cement feed inlet are unreasonable, the mixing shaft cannot be quickly and fully mixed, and it is easy to form the phenomenon of shaft holding.

或者是搅拌主机进水管与冲水位置原因。冲水点位置和冲洗方向不正确的话，又或者是冲水压力过低，导致水在进入主机内部后，不能讲暂时粘结在轴上的混凝土冲洗掉，则时间久了就容易形成抱轴。

Or the water inlet pipe and flushing position of the mixing host. If the position and direction of the flushing point are incorrect, or the flushing pressure is too low, so that the concrete temporarily bonded to the shaft cannot be washed off after the water enters the main engine, it is easy to form a shaft holding after a long time.

也可以生产之后没有及时对搅拌机内部进行清洗，或清洗不干净，导致搅拌轴表面仍有残留的混凝土，干燥后凝固在搅拌轴上，如果长期如此则非常容易产生抱轴现象。

It is also possible that after production, the internal part of the mixer is not cleaned in time, or the cleaning is not clean, which leads to the residual concrete on the surface of the mixing shaft, which solidifies on the mixing shaft after drying. If this is done for a long time, it is very easy to produce the phenomenon of holding the shaft.

只有进行基本的维护，我们的工作才能正常进行，如小：

Only by carrying out basic maintenance can our work be carried out normally, such as:

1，如遇雷雨或恶劣天气，小型混凝土搅拌机的吊杆不能使用。吊杆不得在风力大于8级的天气下使用；操作小型混凝土搅拌机吊杆时，所有吊杆应在操作人员的视线范围内。

1. In case of thunderstorm or bad weather, the suspender of small concrete mixer cannot be used. The suspender shall not be used in weather with wind force greater than 8; When operating the suspenders of small concrete mixers, all suspenders shall be within the sight of the operator.

2，启动小型混凝土搅拌机时的危险区域是末端软管摆动的周围区域。面积直径是末端软管长度的两倍。端部软管长度大于3m时，危险区域直径为6m；小型混凝土搅拌机端部软管不得弯曲，端部软管不得放入混凝土中。

2. The dangerous area when starting the small concrete mixer is the area around the end hose swinging. The area diameter is twice the length of the end hose. When the length of the end hose is more than 3m, the diameter of the hazardous area is 6m; The end hose of small concrete mixer shall not be bent, and the end hose shall not be put into the concrete.

3，作为备用支架，以标准方式操作动臂，并注意动臂与导线之间的距离。

3. As a backup support, operate the boom in a standard way and pay attention to the distance between the boom and the wire.

这就要求我们在操作搅拌机前后准备好相关的材料和定期进行其维修检查，还能在一定程度上延长他的使用寿命。更多关于相关内容就来我们网站http://www.zkhntjbc.com咨询看看吧！

This requires us to prepare relevant materials and conduct regular maintenance and inspection before and after operating the mixer, which can also extend its service life to a certain extent. Come to our website for more information http://www.zkhntjbc.com Consult!