In our life, concrete mixer is a special vehicle for transporting concrete. A large water tank is usually installed behind the vehicle to mix the concrete. However, as we need to clean the concrete in the car during long-term use, we will introduce the specific cleaning methods below.

1.准备应急驱动软管，关闭搅拌机，然后拆下液压马达上的高压油管接头。

1. Prepare the emergency drive hose, turn off the mixer, and then remove the high-pressure oil pipe connector on the hydraulic motor.

2.拆下高压油管，并将其与故障车上相应连接器的应急驱动软管连接。

2. Remove the high-pressure oil pipe and connect it with the emergency drive hose of the corresponding connector on the faulty vehicle.

3.发动机搅拌车，其控制手柄设置在卸料位置，以排除车内混凝土。

3. The control handle of the engine mixer is set at the discharging position to eliminate the concrete in the truck.

4.紧急驱动完成后，拆下驱动软管并恢复车辆的原始状态。

4. After the completion of the emergency drive, remove the drive hose and restore the original state of the vehicle.

对于清洁混凝土搅拌车内部混凝土的方法，我们必须已经了解它。为了防止设备在正常运行中因某些故障而受到影响，我希望您在了解这些知识后能够更好地操作设备。

For the method of cleaning the concrete inside the concrete mixer, we must have known it. In order to prevent the normal operation of the equipment from being affected by some faults, I hope you can better operate the equipment after understanding these knowledge.

混凝土搅拌机发动机水温过高

The water temperature of concrete mixer engine is too high

混凝土搅拌机是一种特殊的特殊作业车辆。它具有特定的工作环境，发动机水温不可避免地过高。只要发生这种情况，它就会对设备产生一定的影响。那么如果水温过高，你需要做什么？接下来，小编会告诉你。

Concrete mixer is a kind of special vehicle. It has a specific working environment, the engine water temperature is inevitably too high. As long as this happens, it will have a certain impact on the equipment. So what do you need to do if the water temperature is too high? Next, Xiao Bian will tell you.

混凝土搅拌车在普通道路上使发动机过热。它应尽快减速，将车开到阴凉处，或开到相对凉爽的地方停车，但不要急于关火。

The concrete mixer overheats the engine on ordinary roads. It should slow down as soon as possible, drive to a cool place, or drive to a relatively cool place to park, but don't rush to turn off the fire.

打开引擎盖，让发动机怠速，等待发动机温度逐渐恢复正常。在发动机水温恢复正常后，发动机关闭。然后等待一段时间，直到发动机的水温充分下降，然后检查发动机的冷却水量。

Open the hood, let the engine idle, and wait for the engine temperature to gradually return to normal. After the water temperature of the engine returns to normal, the engine is shut down. Then wait for a period of time until the water temperature of the engine drops sufficiently, and then check the cooling water volume of the engine.

此时，混凝土搅拌车的冷却水量可能严重不足。按照规定的量补充冷却水后，检查冷却系统，确认没有其他故障，并启动发动机继续行驶。还要检查水箱百叶窗是否被异物堵住，风扇叶片的工作状态，发动机皮带是否打滑，以及发动机水泵的运行情况。

At this time, the cooling water of concrete mixer may be seriously insufficient. After replenishing the cooling water according to the specified amount, check the cooling system, confirm that there is no other fault, and start the engine to continue driving. Also check whether the water tank shutter is blocked by foreign matters, the working state of the fan blade, whether the engine belt is slipping, and the operation of the engine water pump.

混凝土搅拌机清洁内部混凝土的办法和发动机水温过高情况的介绍就是这样了，希望对你有帮助。

This is the way to clean the concrete inside the concrete mixer and the introduction of the high water temperature of the engine. I hope it will help you.