如今可以看到建筑工地上天天在施工，搅拌车就不能停，高温天气对自动搅拌车来说也是一个严峻的考验，尤其是发动机高温故障，今天就给大家介绍一下发动机高温故障的办法。

　　Now we can see that the construction site is under construction every day, and the mixer can not stop. The high temperature weather is also a severe test for the automatic mixer, especially the engine high temperature fault. Today, I will introduce the solution to the engine high temperature fault.

　　发动机高温，但是冷却液没有减少，就是说自动搅拌车发动机过热，但是冷却系统工作正常，这时应保持发动机怠速运转，严禁熄火，用冷水浇散热器表面加速降温，在温度下降到50度左右的时候，用湿毛巾旋开水箱盖，进行降温，要检查油尺刻度是否在正常范围内。

　　Engine temperature, not reduce, but the coolant is automatic mixing car engine overheating, but the cooling system work is normal, should maintain the engine idle speed running at this moment, it is forbidden to stall, with cold water poured accelerated cooling radiator surface, when the temperature drops to 50 degrees, use a wet towel to unscrew the tank cover, cooling, to check whether the oil dipstick scale is within the normal range.

　　发动机水温过高，冷却系统循环出现故障的原因有很多，比如节温器，冷却硅油风扇，风扇皮带等损坏导致冷却系统无法正常工作。要保持发动机怠速状态，用冷水给散热器降温。

　　There are many reasons for the failure of engine water temperature and cooling system circulation. For example, the cooling system cannot work normally due to the damage of thermostat, cooling silicone oil fan and fan belt. To keep the engine idle, cool the radiator with cold water.

　　在发动机温度降到80度以下时，采取间断熄火，踩下熄火开关或者拔掉电喷系统传感器，用起动机带动发动机运转，10-15秒为一个运转周期，运转降温，检查机油尺刻度是否在正常范围内。

　　When the engine temperature falls below 80 degrees, take intermittent flameout, step on the flameout switch or unplug the sensor of the efI system, drive the engine with the starter, 10-15 seconds as a cycle, the operation of cooling, check whether the oil ruler scale is in the normal range.

　　自动搅拌车发动机在没有冷却液状态下运转，尤其是在夏天，是会造成严重事故的，这时采用任何冷却水浇散热器的方式降温都是无效的，发动机运转也无法散热。此时在发动机怠速状态下，打开机油加注口，迅速加注润滑油，这主要是因为在彻底缺水状态下，发动机润滑油会随之大量高温蒸发，须迅速补充。

　　When the engine runs without coolant, especially in summer, it will cause serious accidents. At this time, any cooling water pouring on the radiator is ineffective, and the engine cannot dissipate heat. At this time, in the engine idle state, open the oil filling port, quickly add lubricating oil, this is mainly because in the complete water shortage, the engine lubricating oil will then evaporate at high temperature, must be quickly supplemented.

　　自动搅拌车发动机高温故障的办法就到这里，需要去多多进行了解，这样在出现问题时才能冷静处理。更多内容的了解您可以来网站www.zkhntjbc.com看看。

　　The solution to the high temperature failure of the engine of the automatic stirring vehicle is here. It is necessary to understand more, so that when there is a problem, we can deal with it calmly. For more information, you can visit www.zkhntjbc.com.