混凝土搅拌机在安装时候有油污不用慌，掌握技巧很关键，下面小编就来给您讲讲相关的技巧方法。

When the concrete mixer is installed with oil stains, don't panic. It's very important to master the skills. The following editor will tell you about the relevant skills and methods.

搅拌机的液压泵吸油口应安装粗滤器，吸油口应与油箱底部有一定距离； 搅拌机出油口应安装高压精滤器，过滤效果应满足系统工作要求，防止污染。 物料堵塞引起的液压系统故障； 过滤网应安装在搅拌机的液压油箱隔板上，以去除回油过滤器未过滤的杂质。

The oil suction port of the hydraulic pump of the mixer should be installed with a coarse filter, and the oil suction port should be a certain distance from the bottom of the oil tank; High pressure fine filter shall be installed at the oil outlet of the mixer, and the filtering effect shall meet the working requirements of the system to prevent pollution. Hydraulic system failure caused by material blockage; The filter screen shall be installed on the diaphragm of the hydraulic oil tank of the mixer to remove the unfiltered impurities of the oil return filter.

搅拌机的液压缸上应安装金属保护圈，防止污物带入缸内，防止泥水和光辐射侵蚀液压缸造成泄漏； 液压元件安装前应检查、清洗内铁。 灰尘和杂质； 定期检查液压油，一旦油液变质、起泡、沉淀、油水分离等，应立即清洗系统并换油。

Metal protective rings should be installed on the hydraulic cylinder of the mixer to prevent dirt from entering the cylinder and prevent leakage caused by muddy water and light radiation erosion of the hydraulic cylinder; Check and clean the inner iron before installing the hydraulic components. Dust and impurities; Check the hydraulic oil regularly. Once the oil deteriorates, bubbles, precipitates, oil-water separation, etc., clean the system and change the oil immediately.

新油加入搅拌机油箱前，应先静置过滤后再加入。 必要时可设置中间油箱，用于新油的沉淀和过滤。避免“高-档低速”驾驶，这使得油料不完全燃烧，从而积累在油管内形成油泥。

Before the new oil is added into the oil tank of the mixer, it should be filtered before adding. If necessary, an intermediate oil tank can be set for sedimentation and filtration of new oil. Avoid "high gear low speed" driving, which makes the oil incomplete combustion, thus accumulating in the oil pipe to form sludge.

不要长时间的怠速运转和低速行驶，这样是 容易使得油料不完全燃烧，积累形成碳层。使用纯净度和品质达标的油料，油料的纯度高，是的油料能够快速充分的燃烧，这样就会减少油泥的生成量。因此，使用匹配的搅拌机油料显得十分有必要了。

Don't idle for a long time and drive at low speed, which is easy to cause incomplete combustion of oil and accumulation of carbon layer. Use the oil with purity and quality up to standard. The purity of the oil is high. Yes, the oil can burn quickly and fully, which will reduce the amount of sludge. Therefore, it is necessary to use matching mixer oil.

此外及时更换失效油封。混凝土搅拌机上很多动置部位会因安装不妥，轴颈与油封刃口不同心，偏摆而甩油。有些油封使用过久会因橡胶老化而失去弹性。发现渗漏应及时更新。另外，油底壳放油螺塞若未拧紧或回松脱落，容易造成机油流失，继而发生“烧瓦抱轴”的机损事故。

In addition, replace the failed oil seal in time. Many moving parts on the concrete mixer will shed oil due to improper installation, misalignment between the journal and the oil seal blade, and deflection. Some oil seals will lose elasticity due to rubber aging after being used for too long. If leakage is found, it should be updated in time. In addition, if the oil drain plug of the oil pan is not tightened or loosened, it is easy to cause oil loss, and then the machine damage accident of "Bush burning and shaft holding" occurs.

搅拌机安装时出现油污别担心有预防技巧的问题就讲解到这里了，如果您对此有不同的想法可以关注网站http://www.zkhntjbc.com分享出来。

Don't worry about oil stains when installing the mixer. That's all for the prevention skills. If you have different ideas about this, you can follow the website http://www.zkhntjbc.com Share it.