自动混凝土搅拌机发生故障时时候,若没有及时将搅拌罐内的清理出来,时间一久将会凝固,会给我们带来很大的经济损失。那么你知道自动混凝土搅拌机已凝固水泥怎么弄干净?下面介绍下相关的方法吧。
When the automatic concrete mixer fails, if the mixing tank is not cleared out in time, it will solidify for a long time, which will bring us great economic losses. Then do you know how to clean the set cement in the automatic concrete mixer? Here are the relevant methods.
准备好紧急驱动软管,将故障自动混凝土搅拌机熄火,卸下液压马达上的高压油管接头。将救援车熄火,将其液压马达的高压油管卸下,并与故障车上的对应接头用紧急驱动软管相连。发动救援车,将其操纵手柄拨出料位置,故障车内的商品混凝土即被排出。紧急驱动完毕后,将驱动软管卸下,并恢复两车原状。
Prepare emergency drive hoses, turn off the faulty automatic concrete mixer and remove the high-pressure tubing connector from the hydraulic motor. Turn off the rescue vehicle, remove the high-pressure tubing of its hydraulic motor, and connect it to the corresponding joint of the faulty vehicle with an emergency drive hose. Start the rescue vehicle and shift its control handle to the discharging position, and the commercial concrete in the faulty vehicle will be discharged. After the emergency drive is completed, remove the drive hose and restore the two cars to their original condition.
若个方法实行有困难,则必须采用以下方法,立即排出商品混凝土。在托轮和滚道之间放入木楔,以控制搅拌筒的旋转,一定要注意;将发动机熄火,拆松液压马达的一根高压油管,搅拌筒可自由旋转,控制搅拌筒的旋转,使维修孔转到下部,然后打开维修孔,清理出筒内商品混凝土。此时一定要注意,商品混凝土排出完毕后,恢复自动混凝土搅拌机原状。
If the first method executes have difficulty, criterion must use the following method, eduction commodity concrete immediately. A wooden wedge is placed between the supporting wheel and the raceway to control the rotation of the mixing cylinder, and safety must be paid attention to; Turn off the engine, loosen a high-pressure oil pipe of the hydraulic motor, and the mixing cylinder can rotate freely, control the rotation of the mixing cylinder, so that the maintenance hole is turned to the lower part, and then open the maintenance hole and clean out the commercial concrete in the cylinder. At this time, we must pay attention to safety. After the discharge of concrete, restore the automatic concrete mixer to its original state.
另外,直接将
自动混凝土搅拌机发动机外部清洗剂均匀喷洒于浸湿后,搅拌车发动机及引擎室周边,待几分钟后,用纤维毛刷清洗引擎室内所能触及到的所有部件。将自动混凝土搅拌机发动机外部清洗剂喷洒于引擎表面,操作步骤同上,周而复始,直将发动机外表清洗干净。冲洗干净的发动机用半湿性毛巾擦干,并用吸尘吸水风干机将手不易触及到的地方吸干,然后风干。
In addition, directly spray the external cleaning agent of the engine of the automatic concrete mixer evenly on the engine and the surrounding of the engine room of the mixer after soaking. After a few minutes, clean all the parts that can be touched in the engine room with the fiber brush. Spray the external cleaning agent on the engine surface of the automatic concrete mixer. Repeat the procedure as above until the engine surface is cleaned. The rinsed engine is dried with a semi-wet towel, and the area hard to reach by hand is sucked dry with a suction air dryer, and then air dried.
自动混凝土搅拌机已凝固水泥怎么弄干净?在这里讲了两种方法,在自动混凝土搅拌机发生故障的时候,及时清理,将损失降到很低很低才行。如果您想了解更多的内容,就来我们网站
www.zkhntjbc.com咨询吧。
Automatic concrete mixer has set cement how to clean? Here are two methods, in the automatic concrete mixer failure, timely cleaning, will be very low loss to very low. If you want to know more, please consult our website www.zkhntjbc.com.