搅拌机主要使用在工程建筑中，在这样恶劣的环境中，对搅拌机的影响是非常大的，比如搅拌机的轮胎，那么小型搅拌机的轮胎容易发生什么问题呢？

The mixer is mainly used in engineering buildings. In such a harsh environment, the impact on the mixer is very large. For example, the tires of the mixer. What problems are likely to occur with the tires of the small mixer?

搅拌机轮胎材料选用？

Mixer tire material selection?

搅拌机轮胎一般为钢丝胎、纤维胎和尼龙胎，如何匹配合适的搅拌机机轮胎将对您的爱机的性能有直接的影响。许多驾驶员并不了解自己的搅拌机上用的或准备购买的是什么类别的轮胎。

Mixer tires are generally steel wire tires, fiber tires and nylon tires. How to match the appropriate mixer tires will have a direct impact on the performance of your favorite machine. Many drivers do not know what kind of tires they are using or preparing to buy on their mixers.

如果同一辆机上用了不同胎体的轮胎，会影响机的使用性能。因此，在换轮胎时好先了解一下自己机上使用的是什么胎体的轮胎，如果是半钢丝的，仍然选用半钢丝的，如果是全纤维的，就仍然选用全纤维的。

If tires with different carcasses are used on the same vehicle, the service performance of the vehicle will be affected. Therefore, when changing the tire, it is better to know what kind of tire body is used on your machine. If it is half steel wire, it is still half steel wire. If it is full fiber, it is still full fiber.

搅拌机如何造蹭胎壁？

How does the mixer rub against the tire wall?

很多时候，蹭胎壁是在搅拌机靠边时无意中造成的，可能是司机机感不佳，也可能是司机开小差。搅拌机轮胎侧面属于轮胎的薄弱部位，磨损严重的话也会造成轮胎鼓包，带来爆胎的隐患。因此，司机在靠边停机的时候，应该多留心搅拌机与路肩的距离，避免蹭胎壁。

Most of the time, the rubbing of the tire wall is caused unintentionally when the mixer pulls aside, which may be caused by the driver's poor sense of machine or the driver's desertion. The side of the mixer tire is the weak part of the tire. If the tire is seriously worn, it will also cause the tire bulge and bring the hidden danger of tire explosion. Therefore, the driver should pay more attention to the distance between the mixer and the road shoulder to avoid rubbing against the tire wall when pulling over to stop.

搅拌机轮胎偏磨现象？

Mixer tire eccentric wear phenomenon?

很多人认为搅拌机轮胎的偏磨是机轮的外倾角超差造成的，但其实轮胎的偏磨在很大程度上是因前束值的超差造成的，根据从事四轮定位工作多年的技术人员总结的经验和大量的定位检测数据分析认为：正确的前束值完全可以有效的避免轮胎的偏磨。

Many people think that the eccentric wear of the mixer tire is caused by the out of tolerance of the camber angle of the wheel, but in fact, the eccentric wear of the tire is largely caused by the out of tolerance of the toe in value. According to the experience summarized by the technicians engaged in four-wheel positioning for many years and the analysis of a large number of positioning detection data, it is believed that the correct toe in value can effectively avoid the eccentric wear of the tire.

还有一种轮胎偏磨是转向轮大总转角的超差、机轮外倾角和主销倾角的不正确导致的，搅拌机在实际的行驶中，大多数是直线行驶的，转弯、倒机和掉头时的大总转角的时间不多，所以由此引发的偏磨比较少。

Another kind of tire eccentric wear is caused by the out of tolerance of the large total angle of the steering wheel, the incorrect camber angle of the wheel and the kingpin angle. In the actual driving of the mixer, most of them are straight-line driving, and the time for the large total angle of turning, reversing and turning is not much, so the eccentric wear caused by this is relatively small.

小型搅拌机的轮胎容易发生什么问题？我们在这里从三个问题来讲解完毕，总之搅拌机的轮胎还是很重要的，平时要多注意轮胎问题，做好搅拌机轮胎的保养。更多事项就来我们网站http://www.zkhntjbc.com进行咨询吧。

What problems are easy to happen to the tires of small mixers? Here, we will finish the explanation from three questions. In short, the tire of the mixer is still very important. We should pay more attention to the tire problem and do a good job in the maintenance of the tire of the mixer. For more information, please visit our website http://www.zkhntjbc.com Let's consult.